Ronald Schalk ([email protected]) reported (94/1/17) that
Yes, no problem. Just remember to use ctrl-alt-<Fn> to go to a Virtual Console (VC), and you can run any Linux application (dosemu is a linux-application). I've got almost always WP5.1 in a dos session.
[Note: Use ctrl-alt-F7 to switch back to X from dosemu, if X runs on VC7.]
If you have X installed and you have successfully compiled dosemu and run it successfully outside X-windows, you should be able to run "xdos" or "dos -X" right away to bring up a dosemu window. If this does not work, make sure:
1. Dosemu has X support compiled in. This is default, however
if you you have compiled dosemu with "x off" in the
compiletime-settings file you don't have X support. So changing
"x off" to "x on" in the compiletime-settings file, followed by
"make pristine; make; make install" should build
you a dosemu-executable with X support, if you have the
X-libraries installed in /usr/X11R6.
2. Set up your X key-mappings. In an xterm, type
xmodmap -e "keycode 22 = 0xff08"
xmodmap -e "keycode 107 = 0xffff"
These lines fix the backspace and delete keys respectively.
3. Configure the X-related configuration options in your
/etc/dosemu.conf file.
Alternatively, you can run dosemu inside a color xterm, which is not recommended because many color xterms have buggy support for the complex text display capabilities of dosemu. This does not require X_SUPPORT to be compiled into dosemu. However, if you really want to do this, do the following steps:
1. Install ansi_xterm. The recommended package is available as:
tsx-11.mit.edu:/pub/linux/ALPHA/dosemu/Development/ansi-xterm-R6.tar.gz
2. Set up your X key-mappings. In an xterm, type
xmodmap -e "keycode 22 = 0xff08"
xmodmap -e "keycode 107 = 0xffff"
These lines fix the backspace and delete keys, respectively.
3. Configure the terminal-related (not X-related) settings in
/etc/dosemu.conf
Marty Leisner ([email protected]) reported (95/3/31) that
I have xrdb log the following resources
dosxterm*Font: vga dosxterm*geometry: 80x25 dosxterm*saveLines: 25
or I alias "dosxterm" to "term -fn vga -title dosxterm -geometry 80x25 -sl 25"
If you use the xrdb method, all you have to do is run "xterm -name dosxterm"
At present, dosemu is set up to use the MIT shared memory extensions. This extension only works on a local display. If you want to run xdos on a remote display, compile dosemu with "mitshm off" in the compiletime-settings file after a "make pristine" or on the clean source tree(97/2/9).
Check that the vga fonts you installed are listed in the font.dir of the directory you installed the fonts in:
If you installed some X-fonts, like you did when you installed dosemu with X-Support for the first time, "mkfontdir" and then "xset fp rehash" needs to be run. The dosemu install should take care for "mkfontdir" and tells you about "xset fp rehash". Tell us if it doesn't work for you. (97/2/13)hertz:~> grep misc /usr/X11R6/lib/X11/XF86Config FontPath "/usr/X11R6/lib/X11/fonts/misc/" hertz:~> grep vga /usr/X11R6/lib/X11/fonts/misc/fonts.dir vga.pcf vga vga11x19.pcf vga11x19 hertz:~> ls /usr/X11R6/lib/X11/fonts/misc/vga* /usr/X11R6/lib/X11/fonts/misc/vga.pcf /usr/X11R6/lib/X11/fonts/misc/vga11x19.bdf /usr/X11R6/lib/X11/fonts/misc/vga11x19.pcf
Look for the vga11x19 font. (97/2/13)
As stated above, dosemu uses the MIT shared memory extensions by default. Under XFree86 they are only available with Version 3.1.2 and above. If you have an older version, consider to upgrade, or configure dosemu to not use this extension (see last section)(97/2/9).
Marty Leisner ([email protected]) reported (95/3/31) that
Yes. I use nnansi.com under X windows. I find 25, 43 and 50 line mode work properly, however 50 line mode is difficult to use on a 1024x768 screen (unless smaller fonts are used or you use a bigger screen. 43 line mode will resize the xterm window to use 43 lines.